MCB600 SERIES

The MCB600 series of medical rated modular and configurable AC-DC power supplies provide high performance and wide flexibility in an extremely compact package. The series is capable of a steady 600W from a 3 x 5 x 1.6” package, distributed among four independent and isolated slots where any of the six available output modules may be plugged. The output modules are rated for 150W and are available in single nominal output voltages of 5, 12, 24 and 48V, and two double nominal output voltages of 12 and 24V. Thanks to their extremely wide output voltage adjustability range and the possibility to connect modules of the same type in series and parallel, the MCB600 offers an unrivalled flexibility. Advanced functions such as remote output current / voltage control and programming, single slot inhibit and all slots inhibit make the MCB600 interactive with complex medical equipment. Other available signals include power supply AC-Good and output modules Power-Good and +/- Sense Terminals. The MCB600 comes in a closed package with a built-in speed-controlled fan to ensure the required airflow while maintaining minimal operational noise, which ultimately enhances the power supply service life time. Output modules of the same type can be connected in parallel in any number in the same chassis without any OR-ing protection. Paralleling modules across multiple chassis does require OR-ing protection with FET or Diodes. This is also true when operating modules in a N+1 redundant configuration. Protection features include a fuse on AC lines, input under voltage lockout (IUV), output over-current (OC), output short-circuit (SC), output over-voltage (OV) and over-temperature (OT). The MCB600 series complies with the 3.1 edition of the IEC 60601-1 safety standard for medical equipment. It offers 2x MoPP means of patient protection and can be used in non-patient contact and non-patient critical equipment. The MCB600 also complies with the EN55011 EMC Class B limits for conducted and radiated emissions, with the IEC/EN 61000-3, for harmonics, the IEC/EN 61000-4 and IEC/EN 60601-1-2 4th edition for EMC immunity. | The medical grade MDP1200 series of AC-DC power supplies offer increased embedded power in three (3) compact 1U compatible packages, high energy efficiency and wide versatility. The series provides a steady 1200 W of regulated DC power through 180-305 V AC and 1000 W through 85-137 V AC input voltage ranges in a single output of 24 or 48 V DC . The MDP1200 series is available in three (3) compact 1U height compatible packages; one, enclosed with a built-in front mounted pair of fans and two (available only 24V variant), U-shaped chassis with or without protective cover, to facilitate system integration. By converting AC power at a 94% typical efficiency rate, the MDP1200 series generates very little heat allowing for optimal thermal management. The series offers a 12 V DC , 0.5 A and a 5 V DC , 1 A stand-by outputs and the full set of protection features including high breaking capacity fuses on both AC lines, input under voltage lockout (IUV), output over-current (OC), output short-circuit (SC), output over-voltage (OV) and over-temperature (OT). The MDP1200 series supports digital power management over the PMBus™ communications protocol enabling interoperation with and easy integration into a system. In addition, analogue control signals include Power Good (P_OK), Remote On / Off (+/-PS_Inhibit) and Sense terminals (RS + , RS - ). Multiple MDP1200 units may be used in parallel mode for redundancy and / or higher power, made possible with the internal OR-ing and current sharing functions. The dual front-mounted fan version provides the full output rated power up to 60 °C. Its fan rotation speed is digitally controlled to guarantee the minimum required airflow, minimizing audible noise for quiet operation, and enhancing the power supply service life time. Rated power is also achieved in the U-chassis variants, with or without perforated cover, when providing them with an 800 LFM airflow from top side up to 55 °C. All variants can be operated up to 70 °C de-rating the output power. The MDP1200 series complies with the 3 rd edition of the IEC60601-1 and ANSI/AAMI ES/EN 60601-1 safety standards for medical equipment requiring 2x MoPP protection grade. It is suitable for BF rated medical equipment under specific conditions. The MDP1200 series meets the EN 60601-1-2 EMC limits of Class B for conducted and radiated emissions as well as the IEC/EN61000-3 for flicker and harmonics content. It also meets the IEC 60601-1-2 4 th edition for EM immunity.